Packet Tracer 6.0.1 the latest version. In this version can simulate Application Layer protocols, b

Packet Tracer is a simulator Cisco network devices are often used as a medium of learning and training, and also in the field of computer parag foods network simulation study. The program was created by Cisco Systems and is provided free of charge to faculty, students and alumni who have participated in the Cisco Networking Academy. Packet Tracer main purpose is to provide a tool for students and teachers in order to understand the principles of computer networks and also build skills in Cisco network devices.
Packet Tracer 6.0.1 the latest version. In this version can simulate Application Layer protocols, basic Routing RIP, OSPF, and EIGRP, up to the level required in the applicable parag foods CCNA curriculum, so if at first glance this software aims for CCNA classes.
Taget Packet Tracer provides simulation network are real, but there are some limitations such as the removal of some of the commands used in the original instrument, namely a reduction in the Cisco IOS command. Packet Tracer and also can not be used to model the productive network parag foods / active. With the release parag foods of version 6, several features are added, including BGP features. BGP does not include the CCNA curriculum, but including CCNP curriculum.
Packet Tracer is usually used Cisco Networking Academy students through certification Cisco Certified Network Associate (CCNA). Due to restrictions on some of its features, this software is used only as a learning tool, not seabagai Cisco routers and switches replacement.
To create a network configuration, parag foods for starters, should be determined first type of device being used, how many and how to form the network configuration parag foods on newsprint. parag foods Types of connecting cables is determined by the following rules: To connect the different devices, use the cable Straight-through: Router - Switch Router - Hub PC - Switch PC - Hub To connect the same equipment, use a Cross-Over Cable : Router - Router - PC Switch - Switch Switch - Hub To configure the router via a PC using the cable Roll-Over configuration of each device configuration process is an important part of network arrangement. The configuration process on each device parag foods is required to activate the function of the device. The configuration process includes providing the IP address and subnet mask to the interface device interface (on the Router, PC or Server), giving parag foods Routing Table (on the router), labeling the name and so on. After the configuration process is done, the red dots mark the cables connected to the device turns green. There are two configuration modes that can be done: GUI mode (Config mode) and mode CLI (Command Line Interface). Example configuration with GUI mode Click the device to be configured. Select the Config menu. Click on the desired interface. Fill in the IP address and its subnet mask. Do the same for the interfaces and other devices. ICT 8 September 2014 I learned about how to create a LAN 2 floor using 1 router, 3 switches, and 14 PCs with PC dividing parag foods into 2 parts: 1st floor and 2nd floor After that put the switch on each floor and connect the switch and the PC on each floor, each using a straight-through copper wires. After the input IP Address and Default Gateaway by distinguishing one digit at each end of the IP Address of each PC and switches. then connect each floor switches to switch the center and left-click on the central switch and open the CLI tab and then enter the enable command and the command config t and input the number of wires that connect the switches to the 1st floor and 2nd floor Finally enter the command switchport mode trunk. Then do the same thing to the floor switches 1 and 2 floor but input cable numbers that are connected to the central switch. Know Features Features in Cisco Packet Tracer Routers router or Router (English: router) is a device that sends data packets through a network or the Internet to the destination, through a process known as routing. Process Routing occurs at layer 3 (network parag foods layer such as the Internet Protocol) protocol stack (protocol stack) seven-layer OSI model. In the Cisco Packet Tracer there are some devices such as the following routers All the above has its own function such as: Cisco 1841 Cisco 1841 Integrated Services Router provides two 10/100 (100BASE-TX) fixed port Ethernet, two-Speed WAN Interface Card (HWIC ) integrated slot compatible with WAN Interface Cards (WICs) and Voice / WAN Interface Cards (VWICs), and one internal parag foods Advanced Integration Module (AIM) slot. Cisco 2620XM Cisco 2620XM Multiservice Router provides a platform-slot network module with a fixed port 10/100